Differences

This shows you the differences between two versions of the page.

--- articles [2019/02/10 14:05] – [Articles] rrandall
+++ articles [2023/05/14 11:29] – rrandall
@@ Line 1: / Line 1: @@
 ====== Articles ======
+~~NOTOC~~
+<WRAP clear></WRAP>
+<WRAP group>
+<WRAP column 30%>
+[[:articles:iso_9001_articles|{{ :articles:earth-globe-pngrepo-com.png?nolink&100 |ISO 9001 & Related Articles}}]] {{:spacer.gif?10|}}
+<WRAP centeralign>[[articles:iso_9001_articles|ISO 9001 & Related Articles]]</WRAP>
+</WRAP>
+<WRAP column 30%>
+[[:articles:as_910xx_articles|{{ :articles:airplane-pngrepo-com.png?nolink&100 |AS 91xx & Related Articles}}]] {{:spacer.gif?10|}}
+<WRAP centeralign>[[articles:as_910xx_articles|AS 9100 & Related Articles]]</WRAP>
+</WRAP>
-[[https://www.linkedin.com/pulse/7-wastes-lean-story-ar0-richard-c-randall/|The 8 Wastes of Lean… and the story of “AR=0”]]
+<WRAP column 30%>
+[[:articles:improvement_articles|{{ :articles:hammer-and-wrench-pngrepo-com.png?nolink&100 |Improvement & LSS Articles}}]] {{:spacer.gif?10|}}
+<WRAP centeralign>[[articles:improvement_articles|Improvement & LSS Articles]]</WRAP>
-[[:articles:small_pocket|The “Voice of the Customer”… and the small pocket on jeans]]
+</WRAP>
-[[:articles:nist_traceability|NIST Traceability Numbers - The Sasquatch of Metrology]]
+<WRAP clear></WRAP>
-[[:articles:optimizing_calibration_intervals|Optimizing Calibration Intervals]]
+<WRAP group>
+<WRAP column 30%>
+[[:articles:qms_auditing_articles|{{ :articles:magnifying-glass-tilted-left-pngrepo-com.png?nolink&100 |QMS Auditing Articles}}]] {{:spacer.gif?10|}}
+<WRAP centeralign>[[:articles:qms_auditing_articles|QMS Auditing Articles]]</WRAP>
+</WRAP>
-[[:articles:Calipers-advantages_and_disadvantages|Calipers: Advantages and Disadvantages of the 3 types]]
+<WRAP column 30%>
+[[:articles:metrology_articles|{{ :articles:micrometer-pngrepo-com.png?nolink&100 |Metrology (Calibration) Related Articles}}]] {{:spacer.gif?10|}}
+<WRAP centeralign>[[:articles:metrology_articles|Metrology (Calibration) Related Articles]]</WRAP>
+</WRAP>
-[[:articles:triz_application|Continuous Improvement... and TRIZ]]
+<WRAP column 30%>
-====== Videos ======
+[[:articles:risk_ca_articles|{{ :articles:red-flag-pngrepo-com.png?nolink&100 |Risk & Corrective Action Related Articles}}]] {{:spacer.gif?10|}}
+<WRAP centeralign>[[articles:risk_ca_articles|Risk & Corrective Action Related Articles]]</WRAP>
+</WRAP>
+<WRAP clear></WRAP>
+<WRAP group>
+<WRAP column 30%>
+[[:articles:other_articles|{{ :articles:openmoji-bookmark-tabs_1f4d1.png?nolink&100 |Other Articles}}]] {{:spacer.gif?10|}}
+<WRAP centeralign>[[:articles:other_articles|Other Articles]]</WRAP>
+</WRAP>
+</WRAP>
+ \\
+ \\
+ \\
+ \\
+<sub>All of the above icons were obtained from [[https://www.pngrepo.com/|PNG Repo]] and are distributed under either the [[https://opensource.org/license/apache-2-0/|Apache License]] or the [[https://creativecommons.org/share-your-work/public-domain/cc0/|CC0 License]].</sub>
-===== How to Metrologically Confirm (a.k.a. "calibrate") Vernier, Dial or Digital Calipers =====
-This video (from Ruby Metrology) shows user's how to check or verify Vernier, Dial and/or Digital Calipers performance (wear pattern of OD jaws, ID jaws, Depth & Step Parameters) by using Multi-function, Multi-dimensional Length Standard Quick Check. All sides of Quick Check are usable.
-{{ :articles:caliper_calibration.mp4 |}}